Just How to Remove and Change a Tub
Just How to Remove and Change a Tub
Blog Article
Are you currently hunting for guidance around Installing A Bathtub?
Setting up a bath tub isn't specifically brain surgery, yet it does need strong plumbing, carpentry, and also occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old bathtub is conveniently available, the job can relocate rapidly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to move out the old tub as well as embeded in the new one. See to it you have qualified yourself for the task as well as fit trying it. Rather than employing a service provider to take over a halfway-completed project, it is much better to think about using one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This article will assist you mount a brand-new bath tub in your bathroom if you have actually already purchased a new tub and don't need to alter the plan of your previous water system pipelines.
Your devices and also product list should comprise the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited accessibility that is usually the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a towel prepared for the staying water that will certainly originate from the pipelines. When the supply pipes have been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Prior to proceeding to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the tap finishes first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Mounting the Tub
Utilizing both wood boards under its feet, put the bath tub in the needed placement. The wooden boards are handy in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 little points.
The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by checking the level and also readjusting the feet on the tub until the spirit level reviews level.
To mount taps, fit the bottom of the outermost versatile faucet connector to the proper supply pipeline by making a compression join; then do the very same for the various other tap.
Turn on the water supply as well as check all joints as well as brand-new pipework for leaks as well as tighten them if needed. Fill the bathtub as well as additionally check the overflow outlet as well as the regular outlet for leaks.
Ultimately, repair the bath paneling as described in the maker's instruction manual. Tiling and securing around the tub needs to wait up until the bath tub has been utilized a minimum of when as this will certainly settle it into its final setting.
Getting ready for the Installment
Firstly, the supporting framework supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you use all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final placement.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, creating the water to permeate the wall in between the bathroom as well as the tiling, leading to complications with wetness as well as possible leakages to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, and are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill the bath tub with water before sealing, to permit the movement experienced when the bathtub is in usage. The sealer can break rather very early if you do not take into consideration this activity before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily offered on the market. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that page on How to Install a Bathtub Yourself when browsing the web. Sharing is caring. You won't know, you could be helping someone out. We take joy in reading our article about Installing A Bathtub.
Visit Website
Report this page